Latest News

May 10, 2016

Graffiti Removal


The Village of Lansing and Lansing Police Department wished to inform residents that the Cook Co. Graffiti removal program has been discontinued by the Cook Co. Sheriff’s Department due to budgetary constrictions.  Both the Village and Police Department are disappointed that this program has been discontinued as it was our sole resource to utilize to have graffiti removed from properties within the Village of Lansing.  With this resource discontinued, we are asking property owners who are affected by graffiti incidents to first contact the police department to report the incident, then to have the graffiti removed.   Property owners may choose to remove the graffiti themselves or hire a private vendor for this removal.  



Standard Graffiti Removal

The following are tips for removing graffiti from various types of surfaces. The city does not endorse specific brands of products, but rather uses brand names to help the consumer identify these graffiti removal materials and supplies.

Metal Surfaces:

  • Try wiping graffiti with any common paint thinner (ex: mineral spirits, lacquer thinner, acetone), or try graffiti removal products such as "Goof Off." Sometimes wiping the graffiti with light penetrating oil such as "WD-40" or "Three-in-One" will remove it.
  • If graffiti still remains, try to remove it by rubbing with steel or bronze wool, or light sandpaper.
  • If graffiti still remains, try power-washing it with a 3000psi pressure washer.
  • If none of these methods work, paint over the graffiti.

Wood Surfaces:

  • If the wood is not weathered and is sealed with paint, stain or sealer, try to remove it by wiping it with mineral spirits. If the wood is weathered, do not use this technique, as the mineral spirits will be absorbed by the wood, driving the paint further down into the wood.
  • Power washing with a 3000psi pressure washer can be used, however, observe carefully to make sure the pressure is not driving the paint deeper into the wood grain.
  • If these methods do not work, sand the wood and re-paint or simply paint over the graffiti.

Plastic Surfaces:

  • Try wiping graffiti with a light, penetrating oil such as "WD-40" or "Three-in-One". Do not use paint thinners as they can soften the plastic and can cause clouding (if clear plastic) or permanent tackiness of the surface.
  • Sometimes a light rubbing with ultra-fine steel or bronze wool will remove the paint.
  • If these methods do not remove the graffiti, paint over it.

Masonry Surfaces:

 

  • The best option for this type of surface is to power-wash the graffiti with a 3000psi-pressure washer. Be careful in selecting the type of tip you use in the pressure wand. Too narrow of a tip (such as a 0 degree) will etch the masonry surface, leaving a perfect outline of the graffiti removed.
  • Sand-blasting is another removal option. As with pressure washing, be careful not to allow the sandblasting tip to remain in one spot too long as it can permanently etch the surface. Be sure to keep the tip moving over the painted area and the surrounding areas so that the surface is blended.
  • If power-washing or sand-blasting does not remove the graffiti, the next best option is to paint over the graffiti.

Glass Surfaces:

  • The best method for removing painted graffiti from glass is to use a razor blade to carefully scrape it off. This method is 99% effective. Use the razor blade in a holder and scrape at a 30-degree angle to the glass.
  • If the paint does not come completely off after using the razor blade, use ultra-fine bronze wool with water to gently rub the remaining paint off.
  • You can use paint thinners on glass, however the razor blade method is much quicker and more environmentally friendly.

*Always read product labels and follow all manufacturer instructions and recommendations. Most of the products identified above are flammable-use caution and follow safety directions when using these products. Always use proper safety clothing and equipment (including gloves, safety glasses, etc.). It is recommended that a small "test" area be done prior to a full application of any product.